K Tool International KTI70382 BEARING SEPERATOR 0-4-1/4IN.

BEARING SEPERATOR 0-4-1/4IN.

K Tool International BEARING SEPERATOR 0-4-1/4IN. - T10 Features: - Remove and replace bearings from locknuts, acorn nuts and spindles - Removes both right and left hand inner races - Open end is slit for easy insertion into the hex flats of a spindle or the flats of a locknut

The K Tool International KTI70382 BEARING SEPERATOR 0-4-1/4IN. Offers a long lasting tool for one stop repair work. Tolerances are machined within .0005" per inch/100" of run. Precision angle is used for exact shaft alignment every time.

The K Tool International KTI70382 BEARING SEPERATOR 0-4-1/4IN. is simple to use and a great value for the handyman or do-it-yourselfer. You can depend on this Bearing Separator for quality and performance every time.

K Tool International KTI70382 Bearing Separator 0-4-1/4in. is a simple and versatile tool that helps keep bearings and races clean and free of contaminants which could be detrimental to their operation. The bearing separator allows oil or grease to drain from the bearing without removing the seal, eliminating the need for disassembly.

K Tool International KTI70382 Bearing separator 0-4-1/4 in. features a sharp, hardened steel blade that fits 0 to 4 inch shank jaws. The blade is housed in an aluminum frame with high elasticity grips that are secured with set screws.

This K Tool International 0-4-1/4" Bearing and Bushing Separator has a composite body and comfortable, rubber cushioned handle. The blade tip on the separator slips in easily between the bearing and the axle casing, then the serrated blade edge presents teeth to pierce the outer bearing race to allow the inner bearings to be pulled out.

This tool is designed to remove bearing balls or other separator members from long and short shafts with an outside diameter of 0 to 4-1/4 inches. The push rod spring holds the push rod open, allowing the ball or other employee to be easily removed.

BEARING SEPERATOR 0-4-1/4IN.

K Tool International BEARING SEPERATOR 0-4-1/4IN. - T10 Features: - Remove and replace bearings from locknuts, acorn nuts and spindles - Removes both right and left hand inner races - Open end is slit for easy insertion into the hex flats of a spindle or the flats of a locknut

The K Tool International KTI70382 BEARING SEPERATOR 0-4-1/4IN. Offers a long lasting tool for one stop repair work. Tolerances are machined within .0005" per inch/100" of run. Precision angle is used for exact shaft alignment every time.

The K Tool International KTI70382 BEARING SEPERATOR 0-4-1/4IN. is simple to use and a great value for the handyman or do-it-yourselfer. You can depend on this Bearing Separator for quality and performance every time.

K Tool International KTI70382 Bearing Separator 0-4-1/4in. is a simple and versatile tool that helps keep bearings and races clean and free of contaminants which could be detrimental to their operation. The bearing separator allows oil or grease to drain from the bearing without removing the seal, eliminating the need for disassembly.

K Tool International KTI70382 Bearing separator 0-4-1/4 in. features a sharp, hardened steel blade that fits 0 to 4 inch shank jaws. The blade is housed in an aluminum frame with high elasticity grips that are secured with set screws.

This K Tool International 0-4-1/4" Bearing and Bushing Separator has a composite body and comfortable, rubber cushioned handle. The blade tip on the separator slips in easily between the bearing and the axle casing, then the serrated blade edge presents teeth to pierce the outer bearing race to allow the inner bearings to be pulled out.

This tool is designed to remove bearing balls or other separator members from long and short shafts with an outside diameter of 0 to 4-1/4 inches. The push rod spring holds the push rod open, allowing the ball or other employee to be easily removed.